該頁(yè)無(wú)縮略圖
使用說(shuō)明書(shū)
BW34-15A MAX
BW34-SUB18A MAX
PSS2825
TUBE15
OPERATIONS MANUAL
BW34-15A MAX
Professional Molded Loudspeaker
Thank you for purchasing our product. Before using the speaker, please read this instruction manual
carefully to ensure correct use.
Specification:
? 2-way with active filter
? HF Driver: 6.7\", 3\" VC
? Woofer: 15\", 4\" VC
? Amplifier type: Class-D Bi-amp
? Power Rating RMS: 1400W
? Power Rating MAX: 2800W
? Frequency response(-10dB): 45Hz - 20KHz
? MAX SPL: 130dB / 136dB(Peak)
? Input connectors: XLR
? Output connectors: XLR Balanced
? DSP Processor
? RS485 Network
? Enclosure: plywood
Cautions:
1. All operating instructions should be read before using this equipment.
2. To reduce the risk of electric shock, do not open the unit. There are NO REPLACEABLE PARTS
INSIDE. Please refer servicing to a qualified service technician.
3. Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.
4. This unit should be cleaned only with a damp cloth. Avoid solvents or other cleaning
detergents.
5. When moving this equipment, it should be placed in its original carton and packaging. This
will reduce the risk of damage during transit.
6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.
8. Make sure ALL of your equipment is completely OFF and lower ALL VOLUME, LEVEL & GAIN
controls before connecting the speaker.
9. ONLY LINE LEVEL SIGNALS CAN BE SENT TO YOUR SPEAKER.
Disregarding any of the above will void your warranty!!!!!
-1-
EQ MODE
SIGNAL
POWER
AMP STATUS
LIMIT
MAIN LEVEL HIGH ADJUST
FLAT
LIVE
VOCAL
DJ
USER
MIN MAX -6 dB +6
PUSH
PUSH
NETWORK BALANCED:10KΩ
ACTIVE LINK
RS 485 IN
RS 485 LINK
SIG INPUT
SIG LINK
BW34-15A MAX
POWER
CAUTION:
TO PREVENT ELECTRIC
SHOCK DO NOT REMOVE
TOP OR BOTTOM COVERS.
WARNING:
TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT
EXPOSE THIS EQUIPMENT TO RAIN
OR MOISTURE
INPUT
~100-240V 50/60Hz
AMPLIFIER FUNCTION
1. RS 485 network data communication input: Use network data lines to connect
RS485/USB converters to PC machines. Relevant operations can be performed
through the software downloaded from PC.
Download link: https://we.tl/t-p6mwiq2d6F
The ACTIVE light ffashes when the data is connected
2. RS 485 network data communication output: Used to connect multiple devices
simultaneously.
The LINK lights on when the network is successfully connected to the next device.
3.Audio signal input: Used to connect mixer and other audio signal sources.
4. Audio signal output: Use XLR connector balanced or unbalanced.
5. Volume control.
6. High frequency control: Adjust the high frequency between -6dB and +6dB.
7. Power indicator.
8. Limiter indicator: The red light illuminated when the audio signal reaches the
maximum output power of the speaker, the input signal will be restricted. Adjust
the level control and HF control appropriately if the red light illuminated continuously.
9. Signal indicator: The LED lights up when signal input.
10. EQ mode selection: 5 modes can be selected(FLAT/LIVE/VOCAL/DJ/USER).
11. Power switch: Turns the system ON and OFF. Ensure that the system volume control is minimized when turned on.
12. Power supply inlet.
Make sure ALL of your equipment is completely OFF and lower ALL VOLUME, LEVEL & GAIN controls before
connecting the speaker.
CONNECTIONS:
1. For this unit you can connect a mixer or other audio signal sources directly into your speaker. Use XLR
connector to connect to the signal input(3) .
2. You can LINK additional speakers using the signal link(4) connection. The amplifier on your speaker will only
power this speaker. If you LINK to additional speakers those speakers must be self amplified.
2
1 3 6
7
8
9
10
11 12
5
4
*Prepare a RJ45/USB
converters if necessary
-2-
Pro Speaker Management System
OPERATION
Home page
Quick Scan page
The Home screen is the first screen which appears after you launch the Pro Speaker Management
System software. Access to main menu/System information/Load & Save/Quick Scan/Sound Check.
Also 5 quick access functions:
- Zoom + : To maximize blocks on main menu page.
- Zoom - : To minimize blocks on main menu page.
- Input Level : Press this button for a quick view of input level in all speaker blocks.
- Output Level : Press this button for a quick view of output level in all speaker blocks.
- Temperature level: Press this button for a quick view of amplifier temperature level in all speaker blocks.
- Connect your speaker(s) to the RS485 computer interface.
- Check if the right PORT is selected for your RS485 interface.
- Press “RESET NETWORK”.
- Press “DEVICE DISCOVERY” button, to find the speaker(s) connected to the RS485 network.
? Once the discovery finished, the message “Stop Discovery” will appear.
? The connected speakers will appear.
- Press “START CONTROL” to access speaker’s features and controls.
NOTE: In this Quick Scan page , you have the DEMO function which allows you to have a look on general
features and functions of the “Pro Speaker Management System” without connecting any speaker.
-3-
Once your speaker detected on the RS485 network, you can START CONTROL.
The “speaker box” of your BW34-15A MAX is now accessible.
- The green light on top left of the box confirms your BW34-15A MAX system is well connected on network.
- 3 main functions are available:
? (Group selection)
? (MUTE)
? (MENU)
Group selection:
Very convenient if you want to adjust several speakers at same time.
Example: If you have 2x BW34-15A MAX systems connected. one on right side and one on left side, you
can adjust crossover parameters, EQ parameters, levels … on both speakers at same time.
Just select the same group for the 2 systems.
Home page with SPEAKER BOX
NOTE: Up to 6 groups of speakers can be created.
-4-
MUTE:
Press this button to mute the complete system.
NOTE:
You can press any “quick access button” (Input LEVEL, Output LEVEL or Temperature LEVEL) at any
time. The speaker box will display the LEVEL selected.
MENU:
Press this button to access speaker parameters.
System information page
Displays your connection status and the software version.
-5-
- Save your project, Load a project, Rename a project
Project files will be saved in your computer system file, in folder “AudioRS485” automatically created
when you have installed the Pro Speaker Management System in your computer.
Load & Save page
Very useful tool for your sound checking. Turn “ON” PINK NOISE GENERATOR and adjust your
speaker SPL curve with external spectrum analyzer.
Sound Check Page
-6-
Monitoring Page
Monitor your system in real-time. From this page you can separately MUTE the top speaker and the
Sub bottom speaker.
Adjust here the low-cut frequency to protect your system or to adjust low cut frequency if you use
an extra SUBWOOFER.
HPF Filter Page
SPEAKER BOX (MENU)
-7-
This EQ page is for general EQ of your system. This is a parametric EQ with 6 EQ points. You can adjust
Frequency, Gain and Slope for each separate EQ point. You can select “Bell”, “Low Shelf” or “High Shelf” curve.
Also available on this page the “MODE” button, to select one of the 5 EQ presets.
EQ Page
Protect your system. As a professional limiter section, you can adjust: Threshold, Attack, Release and
Ration adjustments.
Limiter Page
-8-
You may need to add delay on your speaker system depending on its position in your installation. You
don’t need external speaker management system. You can do it directly with the BW34-15A MAX
software.
To help you on delay adjustment , the delay is displayed in M(meter), ms( Millisecond time) and FT(feet)
Delay Page
-Save your project, Load a project, Rename a project
Project files will be saved in your computer system file, in folder “AudioRS485” automatically created
when you have installed the Pro Speaker Management System in your computer.
Load & Save page
-9-
This protected menu is exclusively dedicated to Sound engineer or qualified service department.
It is not for end user !
WARNING!
All parameters from this EXPERT menu must be carefully adjusted. Wrong adjustments can
definitively damage the speaker system.
PASSWORD : 88333942
This EXPERT menu gives you access to the deeper parameters of the speaker system. You will be able
to change internal electronic crossover parameters, to add limiter , delay or parametric EQ for each
separate driver.
Expert Menu
NOTE: From this menu, you cannot adjust the general HPF, EQ, LIMITER or DELAY parameters.
If you need to adjust them , you need to go back to main menu and exit the EXTERT mode.
-10-
A crossover is used to divide the broadband signal into separate frequency bands. This allows each
driver in a speaker system to be operated within its optimal frequency range. Using active crossover
increase the efflciency of each driver but also of the amplifier by lowering the intermediation
distortion.
The Pro Speaker Management System software crossover module provides a combination of high
pass and low-pass filters.
Each LF or HF filter have selectable Butterworth , Linkwitz-Riley or Bessle filter types and filter slopes
ranging from 12dB/octave to 48dB/octave.
A (PHASE) button is available. Phase or Polarity inversion is used to match driver polarity in systems
which require it. It depends on the filter type you have selected.
Each adjustable frequency band : LF and HF will contain their own set of parameters :
- High-Pass, from 20Hz to 22KHz with Butterworth , Linkwitz-Riley or Bessle filter types and filter
slopes ranging from 12dB/octave to 48dB/octave.
- Low-Pass, from 20Hz to 22KHz Butterworth , Linkwitz-Riley or Bessle filter types and filter slopes
ranging from 12dB/octave to 48dB/octave.
- Gain :from -40dB to +20dB
EXPERT X-OVER PAGE
-11-
Access to Parametric EQ for each driver: HF and LF .
They are all based on same 6-bands output processing interface designed exclusively for speaker
tuning.
I n a per fec t world, each loudspeaker driver would show a ultra-ffat frequenc y response.
Unfortunately, loudspeaker drivers don’t have extremely ffat response by design and require some
adjustments to achieve a more ffat frequency response. These output Parametric EQ can be adjusted
to manually improve frequency response for each driver.
For each EQ point, you can adjust :
- Frequency – From 20Hz to 22KHz
- Gain – From -12dB to + 6dB
- Q-ratio – From 0.27 to 15
You can also choose between 3 shelving EQs: Bell, Low Shelf and High Shelf.
NOTE:
To come back to main EXPERT menu page, just press again on “EXPERT” top page label.
EXPERT PEQ PAGE
-12-
Powerful limiter for each separate driver.
you can adjust : Threshold, Attack, Release and Ration parameters.
NOTE:
Limiter page interface is same for HF and LF section.
EXPERT LIMITER PAGE
-13-
Each driver may need internal delay to have correct time alignment with the other drivers .
To help you on delay adjustment, the delay is displayed in M(meter), ms( Millisecond time) and
FT(feet)
NOTE:
Delay page interface is same for HF and LF section.
EXPERT DELAY PAGE
-14-
OPERATIONS MANUAL
BW34-SUB18A MAX
Professional Active Subwoofer
Thank you for purchasing our product. Before using the speaker, please read this instruction manual carefully to ensure correct use. After reading the manual, store it in a safe place for future reference.
SUBWOOFER SPECIFICATION:
? System type: 18\" Active subwoofer
? RMS power: 2000W
? LF driver: 18\" woofer, 4\" VC
? Amplifier: CLASS-D
? Freq. Range(-10dB): 32Hz-150Hz
? MAX SPL: 130dB/136dB(peak)
? Input connector: XLR
? Output connector: XLR
? Phase: Phase select switch
? Functions: DSP Processor, RS485 Network
? Enclosure: Plywood
CAUTIONS:
1. All operating instructions should be read before using this equipment.
2. To reduce the risk of electric shock, do not open the unit. There are NO REPLACEABLE PARTS INSIDE.
Please refer servicing to a qualified service technician.
3. Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.
4. This unit should be cleaned only with a damp cloth. Avoid solvents or other cleaning detergents.
5. When moving this equipment, it should be placed in its original carton and packaging. This will reduce
the risk of damage during transit.
6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.
8. Make sure ALL of your equipment is completely OFF and lower ALL VOLUME, LEVEL & GAIN controls
before connecting the speaker.
9. ONLY LINE LEVEL SIGNALS CAN BE SENT TO YOUR SPEAKER.
Disregarding any of the above will void your warranty!!!!!
~100-240V 50/60Hz
SUBWOOFER/AMPLIFIER FUNCTION:
1. RS485 network data communication input: Use network data lines with RJ45
connector to connect PC（Prepare a RJ45/USB converters to convert RS485 if necessary). Relevant operations can be performed through the software (Pro Speaker Management System) download from PC, the ACTIVE indicator will ffash when the data is
connected.
Download link: https://we.tl/t-DjWD2A0F7b
2. RS 485 network data communication output: Used to connect multiple
devices simultaneously.
The LINK lights on when the network is successfully connected to the next
device.
3. Multi-function audio signal input: Used to connect mixer and other audio
signal sources.
4. Audio signal output: Use XLR connector balanced or unbalanced.
5. Volume control.
6. Low pass control: Adjust the low pass frequency between 90Hz and 150Hz.
7. Power indicator.
8. Limiter indicator: The red light illuminated when the audio signal reaches the
maximum output power of the speaker, the input signal will be restricted.
Adjust the level control and HF control appropriately if the red light illuminated
continuously.
9. Signal indicator: The LED lights up when signal input.
10. Phase switch: The subwoofer has phase switch NORMAL and INVERTED. Pressing this switch reverses the
phase of subwoofer output with respect to signal input.
11. Power supply inlet.
12. AC link: Connect the power cord output plug to this connector and the other plug to next device.
13. Fuse T10AL, 250V.
14. Power switch: Turns the system On and Offl. Ensure the system volume control at minimum when
switching on.
Make sure ALL of your equipment is completely OFF and lower ALL VOLUME, LEVEL & GAIN controls before
connecting the speaker.
CONNECTIONS:
1. For this unit you can connect a mixer or other audio signal sources directly into your speaker. Use XLR
connector to connect to the signal input(3) .
2. You can LINK additional speakers using the signal link(4) connection. The amplifier on your speaker will
only power this speaker. If you LINK to additional speakers those speakers must be self amplified.
*Prepare a RJ45/USB
converters if necessary
2
1 3 6
7
8
9
10
12 11
13 14
5
4
-2-
Pro Speaker Management System
OPERATION
Home page
The Home screen is the first screen which appears after you launch the Pro Speaker Management System
software. Access to main menu / System information/ Load&Save/Quick Scan/Sound Check
Also 5 quick access functions :
- Zoom + : To maximize blocks on main menu page
- Zoom - : To minimize blocks on main menu page
- Input Level : Press this button for a quick view of input level in all speaker blocks
- Output Level : Press this button for a quick view of output level in all speaker blocks
- Temperature level: Press this button for a quick view of amplifier temperature level in all speaker blocks.
-3-
Quick Scan page
- Connect your speaker(s) to the RS485 computer interface.
- Check if the right PORT is selected for your RS485 interface.
- Press RESET Network
- Press DEVICE DISCOVERY button, to find the speaker(s) connected to the RS485 network.
o Once the discovery finished, the message “Stop Discovery” will appear.
o The connected speakers will appear.
- Press START CONTROL to access speakers features and controls.
NOTE: In this Quick Scan page , you have the DEMO function which allows you to have a look on general
features and functions of the “Pro Speaker Management System” without connecting any speaker.
-4-
Once your speaker detected on the RS485 network, you can START CONTROL.
The “speaker box” of your BW34-SUB18A MAX is now accessible.
- The green light on top left of the box confirms your BW34-SUB18A MAX system is well connected on network.
- 3 main functions are available:
? (Group selection)
? (MUTE)
? (MENU)
Group selection:
Very convenient if you want to adjust several speakers at same time.
Example: If you have 2x BW34-SUB18A MAX systems connected.. one on right side and one on left side, you can
adjust crossover parameters, EQ parameters, levels … on both speakers at same time.
Just select the same group for the 2 systems.
Home page with SPEAKER BOX
NOTE: Up to 6 groups of speakers can be created.
-5-
MUTE:
Press this button to mute the complete system.
NOTE:
You can press any “quick access button” (Input LEVEL, Output LEVEL or Temperature LEVEL) at any time.
The speaker box will display the LEVEL selected.
MENU:
Press this button to access speaker parameters. (pls see next page)
System information page
Displays your connection status and your software version.
-6-
- Save your project, Load a project, Rename a project
Project files will be saved in your computer systemfile , in folder “AudioRS485” automatically created
when you have installed the Pro Speaker Management System in your computer.
Load & Save page
Very useful tool for your sound checking.
Turn ON PINK NOISE GENERATOR and adjust your speaker SPL curve with external spectrum analyzer.
Sound Check Page
-7-
Monitoring Page
Real time monitoring of your system. From this page you can separately MUTE the top speaker and the
Sub bottom speaker.
Adjust here the low-cut frequency to protect your system or to adjust low cut frequency if you use an
extra SUBWOOFER.
HPF Filter Page
SPEAKER BOX (MENU)
-8-
This EQ page is for general EQ of your system. This is a parametric EQ with 6 EQ points. You can adjust Frequency,
Gain and Slope for each separate EQ point. You can select Bell , Low Shelf or High Shelf curve.
EQ Page
Protect your system. As a professional limiter section, you can adjust : Threshold, Attack, Release and
Ration adjustments.
Limiter Page
-9-
You may need to add delay on your speaker system depending on its position in your installation. You don’t need
external speaker management system. You can do it directly with the BW34-SUB18A MAX software.
To help you on delay adjustment , the delay is displayed in M(meter), ms( Millisecond time) and FT(feet)
Delay Page
This EXPERT menu gives you access to the deeper parameters of the speaker system. You will be able to
change the LPF parameter of the SUBWOOFER.
Expert page
-10-
On this page, you can set the LPF frequency of subwoofer, adjust the range of 90-150hz to choose the slope and
type of LPF filter, 12-48dB Butterworth, 12-48dB Linkwitz-Riley or 12-48dB Bessle.
LPF Page
- Save your project, Load a project, Rename a project
Project files will be saved in your computer systemfile , in folder “AudioRS485” automatically created
when you have installed the Pro Speaker Management System in your computer.
Load & Save page
-11-
OPERATIONS MANUAL
PSS2825
Professional Speaker System
Thank you for purchasing our latest professional sound system. This cutting-edge speaker boasts a sleek and stylish design,
while delivering exceptional power and clarity. Before using the speaker, read this instruction manual carefully to ensure
correct use. After reading the manual, store it in a safe place for future reference.
Features:
? D-Class amplifier
? Subwoofer: 2 x 8\", 2\" VC
? Satellite: 2 x 5.25\" woofer, 1.5\" VC
1 x 3.5\" driver, 1.35\" VC
? Stereo Bluetooth
? 5 modes DSP processor
Cautions:
1. All operating instructions should be read before using this equipment.
2. To reduce the risk of electric shock, do not open the unit. There are NO REPLACEABLE PARTS INSIDE. Please refer servicing to a qualified service technician.
3. Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.
4. This unit should be cleaned only with a damp cloth. Avoid solvents or other cleaning detergents.
5. When moving this equipment, it should be placed in its original carton and packaging. This will reduce the risk of
damage during transit.
6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.
8. Make sure ALL of your equipment is completely OFF and lower ALL VOLUME, LEVEL & GAIN controls before connecting
the speaker.
9. ONLY LINE LEVEL SIGNALS CAN BE SENT TO YOUR SPEAKER.
Disregarding any of the above will void your warranty!!!!!
PSS2825
~100-240V 50/60Hz
T6.3AL 250V
1 2 3
6
7
8
10 9
13 14
4 5
12
11
Amplifier Functions:
1. MIC/LINE switch: Use the MIC position when a microphone is
connected. Use the LINE position when a line level source such as an
audio mixing console, audio playback device, or electronic musical
instrument is connected.
2. MIC/LINE input: This balanced input accept a standard XLR or
1/4” jack phone plug. A board range of signals from microphone,
audio mixing consoles and electronic musical instrument may be
connected here. The sensitivity of these inputs are controlled by the
MIC/LINE switch.
3. Volume control for MIC/LINE input.
4. Line in: Use RCA connector input.
5. Bluetooth and Stereo Bluetooth function.
6. Volume control for Bluetooth input.
7. Volume control for subwoofer.
8. Output: Use XLR connector for balanced or unbalanced.
9. Speaker out: Link out to the satellite.
10. DSP preset: Use this button to toggle through the 5 different
settings.
11. Signal indicator.
12. Limit indicator: Illuminated just before the sub amplifier begins
to clip and distort. Adjust the sub level control and signal level from
your source so this illuminates only brieffly on peaks in the music.
Using the system with this on all or much of the time will result in
poor sound quality and damage the speakers and electronics.
13. Power supply input.
14. Power supply switch.
Bluetooth pairing instructions:
1. Press and release the PAIR button, while the pairing light is fflashing and the PSS2825 name should appear on your
pairing device.
2. Click on “PSS2825” on your pairing device to complete pairing.
3. Press the PAIR button again to exit the current connection.
Note: Successfully paired devices and speakers can be automatically connected for the second time.
Stereo Bluetooth function usage:
1. Press and release the STEREO LINK button on both speakers, both speakers should be PSS2825.
2. Press the PAIR button after the two speakers are successfully linked.
3. Search for “PSS2825” on your pairing device and connect.
4. Press the STEREO LINK button again to exit the current link.
Note: When pairing two speakers, try to place the two speakers close together. After the pairing is successful, they can be
placed separately.
You can not start a new pairing or linking request while a device is already connected. Please disconnect the previous
pairing, then you can start a new pairing.
OPERATIONS MANUAL
TUBE 15
COMPACT 3-WAY ARRAY SYSTEM
Congratulations on your purchase of the TUBE 15 array system, the best choice for both live
performers and installers. Elegant and easy to install, this system can be deployed on stage
within minutes. With its onboard Class-D amplifier with DSP control, it provides high-quality sound and controlled directivity. The result is a sound reinforcement system dynamic
enough to use at home, in the studio, parties or in a home theater.
Specification for TUBE 15
? Type: 3-way active speaker
? HF Driver: 1.8\" dirver, 1\" voice coil, Neodymium
? MID Driver: 6 x 3\" woofer
? LF Driver: 1 x 12\" subwoofer, 2.5\" voice coil
? Amplifier: Bi-amp Class-D amplifier
? Frequency Range: 42Hz-20KHz ( -10dB)
? Dispersion ( HxV): 100°x 40° > 1KHz
? Mic/Line Input: XLR or 1/4’’ Jack
? Aux Input: RCA, 3.5mm
? Line Output: XLR
? Audio Processor: DSP processor with Bluetooth connection
? Max SPL: 124dB /130dB(Peak)
? Power capacity: 500W+300W
CAUTIONS:
1. All operating instructions should be read before using this equipment.
2. To reduce the risk of electric shock, do not open the unit. There are NO REPLACEABLE
PARTS INSIDE. Please refer servicing to a qualified service technician.
3. Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.
4. This unit should be cleaned only with a damp cloth. Avoid solvents or other cleaning
detergents.
5. When moving this equipment, it should be placed in its original carton and packaging.
This will reduce the risk of damage during transit.
6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.
8. Make sure ALL of your equipment is completely OFF and lower ALL VOLUME, LEVEL &
GAIN controls before connecting the speaker.
9. ONLY LINE LEVEL SIGNALS CAN BE SENT TO YOUR SPEAKER.
Disregarding any of the above will void your warranty!!!!!
Functions:
1.BACK: Used to return to the previous operation.
2.MIXER: Used to enter the volume adjustment interface, after
entering, you can use the MASTER knob to adjust the total
volume and bass volume.
3.LIMIT indicator: The red light illuminated when the audio
signal reaches the maximum output power of the speaker, the
input signal will be restricted. Adjust the level control and HF control appropriately if the red light
illuminated continuously.
4.USB port for charging.
5.Volume control of MIC input 1.
6. MIC input 1: Use XLR or 1/4” Jack connector balanced or unbalanced.
7. Volume control of MIC input 2.
8. MIC input 2: Use XLR or 1/4” Jack connector balanced or unbalanced.
9. Volume control of LINE/INSTRUMENT input.
10. LINE/INSTRUMENT input: Use 6.35mm Jack connector balanced or unbalanced.
11.Volume control of AUX in.
12. AUX in: Use RCA or 3.5mm Jack connector balanced or unbalanced.
13. Line output: Use XLR connector balanced or unbalanced.
14. MASTER knob：Press to enter the Menu setting page. During operation, turn the knob to select,
press the knob to confirm, and press the BACK to return to the previous directory.
(1). Sensitivity selection of MIC / LINE 1 and MIC / LINE 2.
Select MIC / LINE 1 and MIC / LINE 2, press the master knob to enter, then you can choose LINE or
MIC, press the BACK to return to the previous operation.
(2). DSP preset mode, 4 modes can be selected CLUB, MUSIC, LIVE, SPEECH
(3).Hi-pass filter selection.
(4).Delay selection.
(5). EQ adjustment: Turn the MASTER knob to select the specified parameter, press the MASTER
knob to select, then turn the MASTER knob to adjust.
(6). Bluetooth pairing connection.
A． Bluetooth pairing：Select the interface to enter Bluetooth settings, select PAIR, open your
device to be paired, and search for the Bluetooth name \"TUBE 15\". After the pairing is successful, the interface displays the name of the successfully connected device.
B. Stereo Bluetooth pairing(used to connect two TUBE 15 wirelessly)：Select the interface to
enter Bluetooth settings, select TWS(Only need to set this on one of TUBE 15 ), then connect
through the Bluetooth connection. After the connection is successful, you can play music and
enjoy the stereo effect.
TUBE 15
1 LINE 2 LINE
PRESET:
DELAY:
EQ:
MUSIC
HI-PASS NONE
0ms
IN
BLUETOOTH: IPHONEX
INPUT 1
MIC
LINE
2 LINE
PRESET:
DELAY:
EQ:
MUSIC
HI-PASS NONE
0ms
IN
1 LINE
BLUETOOTH: IPHONEX
FACTORY PRESETS
CLUB
LIVE
SPEECH
MUSIC
Functions:
1.BACK: Used to return to the previous operation.
2.MIXER: Used to enter the volume adjustment interface, after
entering, you can use the MASTER knob to adjust the total
volume and bass volume.
3.LIMIT indicator: The red light illuminated when the audio
signal reaches the maximum output power of the speaker, the
input signal will be restricted. Adjust the level control and HF control appropriately if the red light
illuminated continuously.
4.USB port for charging.
5.Volume control of MIC input 1.
6. MIC input 1: Use XLR or 1/4” Jack connector balanced or unbalanced.
7. Volume control of MIC input 2.
8. MIC input 2: Use XLR or 1/4” Jack connector balanced or unbalanced.
9. Volume control of LINE/INSTRUMENT input.
10. LINE/INSTRUMENT input: Use 6.35mm Jack connector balanced or unbalanced.
11.Volume control of AUX in.
12. AUX in: Use RCA or 3.5mm Jack connector balanced or unbalanced.
13. Line output: Use XLR connector balanced or unbalanced.
14. MASTER knob：Press to enter the Menu setting page. During operation, turn the knob to select,
press the knob to confirm, and press the BACK to return to the previous directory.
(1). Sensitivity selection of MIC / LINE 1 and MIC / LINE 2.
Select MIC / LINE 1 and MIC / LINE 2, press the master knob to enter, then you can choose LINE or
MIC, press the BACK to return to the previous operation.
(2). DSP preset mode, 4 modes can be selected CLUB, MUSIC, LIVE, SPEECH
(3).Hi-pass filter selection.
(4).Delay selection.
(5). EQ adjustment: Turn the MASTER knob to select the specified parameter, press the MASTER
knob to select, then turn the MASTER knob to adjust.
(6). Bluetooth pairing connection.
A． Bluetooth pairing：Select the interface to enter Bluetooth settings, select PAIR, open your
device to be paired, and search for the Bluetooth name \"TUBE 15\". After the pairing is successful, the interface displays the name of the successfully connected device.
B. Stereo Bluetooth pairing(used to connect two TUBE 15 wirelessly)：Select the interface to
enter Bluetooth settings, select TWS(Only need to set this on one of TUBE 15 ), then connect
through the Bluetooth connection. After the connection is successful, you can play music and
enjoy the stereo effect.
LINE 2 LINE
PRESET:
DELAY:
EQ:
MUSIC
HI-PASS NONE
0ms
IN
1
BLUETOOTH: IPHONEX
HI-PASS
30Hz
40Hz
NONE
LINE 2 LINE
PRESET:
DELAY:
EQ:
MUSIC
HI-PASS NONE
0ms
IN
1
BLUETOOTH: IPHONEX
DELAY
1.00 ms
1.13 FEET
0.43 METERS
1 LINE 2 LINE
PRESET:
DELAY:
MUSIC
0ms
EQ: IN
BLUETOOTH: IPHONEX
HI-PASS: NONE
LOW MID
0dB 0dB 0dB
HIGH
EQ
1 LINE 2 LINE
PRESET:
DELAY:
MUSIC
HI-PASS: NONE
0ms
EQ: IN
BLUETOOTH: IPHONEX
BLUETOOTH
PAIR TWS
